SenTech STC-A33A Bedienungsanleitung

Small Cubic TypeVGA CCDMonochrome Analog CameraSTC-A33AApplication Manual

STC-A33A 2. Vertical Timing a. Normal Full Scanning (Settings: Address: 10H, Value: 1XX00XXX; Address: 11H, Value: X000X000) 1 H = 63.5556 µs

STC-A33A c. 1/2 Partial Scanning (Settings: Address: 10H, Value: 1XX01XXX; Address: 11H, Value: X000X001) 1 H = 63.5556 µseconds, 60.0544 Hz 1

STC-A33A e. Variable Partial Scanning (Settings: Address: 10H, Value: 1XX01XXX; Address; 11H, Value: X000X111)

STC-A33A B. Binning Mode (Settings: Address: 10H, Value: 1XX1XXXX) 1. Horizontal Timing 1 CLK = 81.4817 nseconds at 30 fps 1 CLK = 40.7407 ns

STC-A33A 2. Vertical Timing a. Binning Full Scanning (Settings: 10H, Value: 1XX10XXX; Address: 11H, Value: X000X000) 1 H = 63.5556 µseconds,

STC-A33A c. Binning 1/2 Partial Scanning (Settings: Address: 10H, Value: 1XX11XXX; Address: 11H, Value: X000X001) 1 H = 63.5556 µseconds, 112.

STC-A33A IV. Camera Function Mode A. Normal Mode 1. Normal Mode (Frame Exposure) 2. Normal Mode (Electronic Shutter)

STC-A33A B. Pulse Width Trigger Mode In the “Pulse Width Trigger Mode” with positive polarity, the camera exposure starts at the rising edge o

STC-A33A 2. Pulse Width Trigger Mode (Non-Reset, External Sync) Note 1: The camera does NOT switch to the normal

STC-A33A 3. Pulse Width Trigger Mode (Non-Reset, Internal Sync) Note 1: The camera does NOT switch to the normal m

STC-A33A !CAUTIONRISK OF ELECTRIC SHOCKDO NOT OPENCAUTION:TO REDUCE TH E RISK OF EL ECTRIC SHOCK, DO N OTREMOVE COVER (OR BACK). NO USE

STC-A33A C. Edge Preset Trigger Mode In this “Edge Preset Trigger Mode” with positive polarity, the camera exposure starts at the rising edge

STC-A33A 2. Edge Preset Trigger Mode (Non-Reset, External Sync) Note 1: The camera does NOT switch to normal mode

STC-A33A 3. Edge Preset Trigger Mode (Non-Reset, Internal Sync) Note 1: The camera does NOT switch to the normal mode

STC-A33A D. H Reset Mode Normally, the video noise appears when the start of the trigger signal is applied before finishing the video out of t

STC-A33A V. Communication Protocol Specifications This camera has a communication function that enables external devices, such as the PC, to c

STC-A33A C. The Communication Format 1. Sending Data Format from the PC to the Camera is shown below: a. Sending the read command: SOF Dev

STC-A33A D. The Camera Control Command 1. The Camera Command List Notes:  The data unit of each command is 1 byte (8bit).  The data can

STC-A33A Command No. Read / Write Save to EEPROM Function Initial Data Data Range 32H Read / Write X The gain offset (6bit: D[5…0]) The value o

STC-A33A 2. Descriptions of the Camera Control Commands (The underline settings are factory default settings) Command No. Command Descriptions

STC-A33A Command No. Command Descriptions 12H: MOD3[7…0] [The camera function mode 3] Initial data: MOD3[7…0] = 0 This sets the following cam

STC-A33A Contents I. Rear Panel Specifications………………………………………………………………………. 1-2 A. 12pin Connector…………………………………………………………………………. 1 B. DIP Swit

STC-A33A Command No. Command Descriptions 22H: SHR[7…0] 23: SHR[15…8] [The exposure time (CLK) of the electronic shutter] Initial data: SHR

STC-A33A Command No. Command Descriptions 31H: DGB[7…0] [The digital gain] Initial data: DGB[7…0] = The value in the address 0EH, data range: 0

STC-A33A Command No. Command Descriptions 74H: DSW_ST[9…8] 75H: DSW_ST[7…0] [Status of the DIP switch on the rear panel] This obtains the stat

STC-A33A 3. Camera Control Commands (The camera function modes: address 10H, 11H, 12H) a. Normal Mode (90fps) Function Mode Frame rate Binnig

STC-A33A b. Normal Mode (60fps) Function Mode Frame rate Binnig Scanning Method Trigger Mode Reset Mode Trigger Polarity Exposure Start Mode G

STC-A33A c. Normal Mode (30fps) Function Mode Frame rate Binnig Scanning Method Trigger Mode Reset Mode Trigger Polarity Exposure Start Mode G

STC-A33A d. Trigger Mode (90fps, Full scanning) Function Mode Frame rate Binnig Scanning Method Trigger Mode Reset Mode Trigger Polarity Expos

STC-A33A e. Trigger Mode (90fps, Partial full scanning) Function Mode Frame rate Binnig Scanning Method Trigger Mode Reset Mode Trigger Polari

STC-A33A f. Trigger Mode (90fps, 1/2 partial scanning) Function Mode Frame rate Binnig Scanning Method Trigger Mode Reset Mode Trigger Polarit

STC-A33A g. Trigger Mode (90fps, 1/4 partial scanning) Function Mode Frame rate Binnig Scanning Method Trigger Mode Reset Mode Trigger Polarit

STC-A33A i. Trigger Mode (90fps, Binning, Full scanning)…………………………... 36 j. Trigger Mode (90fps, Binning, Partial full scanning)……………………

STC-A33A h. Trigger Mode (90fps, Variable partial scanning) Function Mode Frame rate Binnig Scanning Method Trigger Mode Reset Mode Trigger Po

STC-A33A i. Trigger Mode (90fps, Binning, Full scanning) Function Mode Frame rate Binnig Scanning Method Trigger Mode Reset Mode Trigger Polar

STC-A33A j. Trigger Mode (90fps, Binning, Partial full scanning) Function Mode Frame rate Binnig Scanning Method Trigger Mode Reset Mode Trigg

STC-A33A k Trigger Mode (90fps, Binning, 1/2 partial scanning) Function Mode Frame rate Binnig Scanning Method Trigger Mode Reset Mode Trigger

STC-A33A l. Trigger Mode (90fps, Binning, 1/4 partial scanning) Function Mode Frame rate Binnig Scanning Method Trigger Mode Reset Mode Trigge

STC-A33A m. Trigger Mode (90fps, Binning, Variable partial scanning) Function Mode Frame rate Binnig Scanning Method Trigger Mode Reset Mode T

STC-A33A n. Trigger Mode (60fps, Full scanning) Function Mode Frame rate Binnig Scanning Method Trigger Mode Reset Mode Trigger Polarity Expos

STC-A33A o. Trigger Mode (60fps, Partial full scanning) Function Mode Frame rate Binnig Scanning Method Trigger Mode Reset Mode Trigger Polari

STC-A33A p. Trigger Mode (60fps, 1/2 partial scanning) Function Mode Frame rate Binnig Scanning Method Trigger Mode Reset Mode Trigger Polarit

STC-A33A q. Trigger Mode (60fps, 1/4 partial scanning) Function Mode Frame rate Binnig Scanning Method Trigger Mode Reset Mode Trigger Polarit

STC-A33A I. Rear Panel Specifications A. 12 Pin Connector The connector type: HR10A – 10R – 12PB (Hirose) or equivale

STC-A33A r. Trigger Mode (60fps, Variable partial scanning) Function Mode Frame rate Binnig Scanning Method Trigger Mode Reset Mode Trigger Po

STC-A33A s. Trigger Mode (60fps, Binning, Full scanning) Function Mode Frame rate Binnig Scanning Method Trigger Mode Reset Mode Trigger Polar

STC-A33A t. Trigger Mode (60fps, Binning, Partial full scanning) Function Mode Frame rate Binnig Scanning Method Trigger Mode Reset Mode Trigg

STC-A33A u. Trigger Mode (60fps, Binning, 1/2 partial scanning) Function Mode Frame rate Binnig Scanning Method Trigger Mode Reset Mode Trigge

STC-A33A v. Trigger Mode (60fps, Binning, 1/4 partial scanning) Function Mode Frame rate Binnig Scanning Method Trigger Mode Reset Mode Trigge

STC-A33A w. Trigger Mode (60fps, Binning, Variable partial scanning) Function Mode Frame rate Binnig Scanning Method Trigger Mode Reset Mode T

STC-A33A x. Trigger Mode (30fps, Full scanning) Function Mode Frame rate Binnig Scanning Method Trigger Mode Reset Mode Trigger Polarity Expos

STC-A33A y. Trigger Mode (30fps, Partial full scanning) Function Mode Frame rate Binnig Scanning Method Trigger Mode Reset Mode Trigger Polari

STC-A33A z. Trigger Mode (30fps, 1/2 partial scanning) Function Mode Frame rate Binnig Scanning Method Trigger Mode Reset Mode Trigger Polarit

STC-A33A aa. Trigger Mode (30fps, 1/4 partial scanning) Function Mode Frame rate Binnig Scanning Method Trigger Mode Reset Mode Trigger Polari

STC-A33A B. DIP Switch Settings DIP Switch Settings No. 1 to 3: Shutter Speed Shutter Speed No.1 No.2 No.3 OFF / Pulse Width Trig

STC-A33A ab. Trigger Mode (30fps, Variable partial scanning) Function Mode Frame rate Binnig Scanning Method Trigger Mode Reset Mode Trigger P

STC-A33A ac. Trigger Mode (30fps, Binning, Full scanning) Function Mode Frame rate Binnig Scanning Method Trigger Mode Reset Mode Trigger Pola

STC-A33A ad. Trigger Mode (30fps, Binning, Partial full scanning) Function Mode Frame rate Binnig Scanning Method Trigger Mode Reset Mode Trig

STC-A33A ae. Trigger Mode (30fps, Binning, 1/2 partial scanning) Function Mode Frame rate Binnig Scanning Method Trigger Mode Reset Mode Trigg

STC-A33A af. Trigger Mode (30fps, Binning, 1/4 partial scanning) Function Mode Frame rate Binnig Scanning Method Trigger Mode Reset Mode Trigg

STC-A33A ag. Trigger Mode (30fps, Binning, Variable partial scanning) Function Mode Frame rate Binnig Scanning Method Trigger Mode Reset Mode

STC-A33A Revision Rev Date (D/M/Y) Changes Name Notes 1.0 2/9/2008 New Document Sam Aimono Application Manual

STC-A33A Sensor Technologies America, Inc. 1345 Valwood Pkwy, Suite 320 Carrollton, Texas 75006-6891

STC-A33A II. Input / Output Signal Specifications A. Input Signal Specifications 1. External Sync Signals a. Signal Level: 2.0 to 5.0 Vp

STC-A33A B. Output Signals Specifications 1. WEN (Write Enable) Signal a. Signal Level: 3.3 Vp-p at 10k Ω termination b. Signal Polarity

STC-A33A III. Camera Output Timing Charts A. Normal Mode (Setting: Address: 10H, Value: 1XX0XXXX) 1. Horizontal Timing 1 CLK = 81.4817 nsecon